Nfusion Nova, Phoenix and Solaris Guide
Nfusion Nova, Phoenix and Solaris Guide
New Nfusion SD Instructions:
You have 2 options now – to utilize the SUNS bin using a program called NOI with which you get full EPG (recommended) or use the T54 European bin procedure with which you do not get EPG.
Procedure using NOI
To use NOI you would need a PC connected to the same network as the receiver, but the PC need not be dedicated or physically connected to the receiver. You just need to make sure both PC and receiver can access the internet, and that the PC is on and running NOI whenever you wish to watch TV. NOI can be set to autostart and connect on booting up the PC as well.
Download these files first.
1. Load the boot_g3x_to r3x_v1.23.bin file in BOOT mode. Load only if European conversion like T54/T58 is currently loaded.
2. Load this file u48 factory file from July 2009 also in MAIN mode.
3. Load this file next… boot file v.130 also in BOOT mode.
4. Lastly load this file 090928 sol phoenix sd v153 1 (Maintenance release) in MAIN mode.
5. Then load newest file which is nfusion-154.2-255.bin in MAIN mode.
6. Setup LNBs
7. Scan Channels
8. Go to channel 200 and turn off receiver
6. Start NOI
7. Go to Settings and enter your NFPS Info. and hit save. Be sure to use colons in the key 61:03:40:34:45:40:69:70:98:71:23:41:21:34 (given to you).
8. Go to Main and hit Start. If you see snow your all set.
9. Turn on receiver and watch TV.
Note: You may need to add a rule to your firewall and/or anti-virus shield.
Disable them for a bit to find out if that’s what is blocking the program from working. If so, add rules and it should work fine.
————————————————————————————————————————————————————-
Procedure using t54 bin
==AFTER THIS MESSAGE IS NOT UPDATED AND IS HERE FOR EDUCATIONAL USE ONLY==
1. Go to Order Now and Follow the Instructions, After you have you get the Donation Number Continue Below.
2. You have to get this Archives.
Archive 1 – Download (.ZIP) (.RAR)
Archive 2 – Download (.RAR) (.ZIP)
3. GO TO YOUR RECEIVER CONNECTED, AND CHECK IN Witch DiSEqC PORT IS EACH SATELLITE (110, 119) and the 22Khz if its on or off. (Menu -> Installation -> Antenna Setup and Check them.
Here’s a Picture of what you need.
Video tutorial To Load the Software click here
Now that you have the Software, now you need the channels.
Click here on how to get the channel list.
To get the Channel list of the Satellite 110 you have to take the file called 110 from the second folder and so on for the 119.
If you got 2 Satellite’s Please visit ftazeta and make a new thread in nfusion discussions with the config that you’ve checked so
we make your own configuration.
Load the t54.bin
Open the 1.1 or 1.31 loader and Click on OPEN FILE and select the T54.bin. Make sure you are in MAIN mode and Click on START NFUSING. Click on OK and reboot the receiver and the Bin will start loading. When finished it will show HOLD and then GOOD and then 0001.
The software we are using were made for the European Market and the display format is in the PAL system.
The American/Canadian TV works in the NTSC system and as such we need to convert from PAL to MULTI.
When you connect the Receiver to the TV and Start the receiver, you will find a scrolling screen. Change the Channel with your remote to either channel 3 or Channel 594 which are FREE channels in the Dish Network system. These channels are not encoded and so have a picture. You will hear sound of people talking with the picture scrolling vertically. Press the following Buttons on your Receiver Remote in the following order.
Press the Menu Button, press once the DOWN Channel button, Press OK, Press the DOWN Channel buttonagain, and finally press the Left or Right Volume button once. You should now see a Blue screen with MULTI shown.
Press Up button and change all the Languages to English.Press Exit. And you will see the Free Channel.Now we need to enter other information like the code etc.Press Menu>Internet>OK>NEWCAMD>press 9949 (you will not see any change)>press OKIt should take you to another Page, Click OK on Server Setting 1 and it will open another Page.
This is where you will enter all the other important information.The first line “Server Address” – It should read – fenfu.dynsite.net or fenfui.dynite.net or any other server as given to you – EXIT to saveNext line is “User Name” – Here you have to input the Donation # assigned to you by NFPS. – EXIT to save
Next is Password – Here too you input the same Donation # – EXIT to save
DONATION #. Please note each number you enter make sure it is showing on the screen. Check and recheck before you save.
The next line is DES Keys – These will be already entered. However if you should need it then here it is: 6103403445406970987123412134
Next Line is Port1 – Here you will enter the Port assigned to you. Although the Port may be the correct one you need to reenter the Port. – EXIT to Save. Now you will have a Black screen.
You will need to do a Hard Reboot. Shut OFF and ON the receiver with the rear Rocker switch.The screen will scroll. Check that you have Channel 594 or 3 showing on the receiver panel. Press SIZE button to stop the scroll.Again go back to NEWCAMD and change it from OFF to ON. Press Exit.
Again go back into SERVER SETTINGS and Exit out of it. Reboot. Press SIZE to stop the scroll.Now press any channel number and you should be up and running. If not then go back into Server Settings, Exit, Reboot Press SIZE to stop the scroll. Now again select the channel you want.Watch and enjoy TV.
THAT’S IT, NOW WATCH TV!